* Sea-Bird SBE19plus Data File: * FileName = C:\newfiles\050809\050809072.hex * Software Version 1.59 * Temperature SN = 4647 * Conductivity SN = 4647 * System UpLoad Time = May 11 2009 10:36:05 ** Date ** Samplers ** Station Name ** Lat/Long * ds * SeacatPlus V 1.4D SERIAL NO. 4647 11 May 2009 9:43:44 * vbatt = "12.6," vlith = "8.4," ioper = 61.9 "ma," ipump = 0.4 "ma," * iext01 = 38.7 "ma," iext23 = 6 "ma," * status = not logging * number of scans to average = 1 * samples = "118237," free = "323268," casts = 84 * mode = "profile," minimum cond freq = "3357," pump delay = 40 sec * autorun = "no," ignore magnetic switch = no * battery type = "ALKALINE," battery cutoff = 7.5 volts * pressure sensor = strain "gauge," range = 508 * SBE 38 = "no," Gas Tension Device = no * Ext Volt 0 = "yes," Ext Volt 1 = "yes," Ext Volt 2 = "yes," Ext Volt 3 = yes * echo commands = yes * output format = raw HEX * S> * * SeacatPlus V 1.4D SERIAL NO. 4647 11 May 2009 9:44:01 * temperature: 3-Feb-09 * TA0 = 1.27E-03 * TA1 = 2.54E-04 * TA2 = 1.16E-06 * TA3 = 1.04E-07 * TOFFSET = 0.00E+00 * conductivity: 3-Feb-09 * G = -1.05E+00 * H = 1.29E-01 * I = -2.34E-04 * J = 3.33E-05 * CF0 = 2.86E+03 * CPCOR = -9.57E-08 * CTCOR = 3.25E-06 * CSLOPE = 1.00E+00 * pressure S/N = "5724," range = 508 psia: 3-Feb-09 * PA0 = 2.70E-02 * PA1 = 1.55E-03 * PA2 = 7.31E-12 * PTCA0 = 5.25E+05 * PTCA1 = 3.00E+00 * PTCA2 = -1.28E-01 * PTCB0 = 2.51E+01 * PTCB1 = -4.00E-04 * PTCB2 = 0.00E+00 * PTEMPA0 = -7.56E+01 * PTEMPA1 = 4.80E+01 * PTEMPA2 = -1.95E-01 * POFFSET = 0.00E+00 * volt 0:00 offset = "-4.584737e-02," slope = 1.25E+00 * volt 1:00 offset = "-4.602316e-02," slope = 1.25E+00 * volt 2:00 offset = "-4.584000e-02," slope = 1.25E+00 * volt 3:00 offset = "0.000000e+00," slope = 1.00E+00 * EXTFREQSF = 1.00E+00 * dh * cast 72 8 May 2009 10:34:47 samples 95213 to "96510," avg = "1," stop = mag switch * S> # nquan = 16 # nvalues = 10 # units = specified # name 0 = prdM: "Pressure," Strain Gauge [db] # name 1 = tv290C: Temperature "[ITS-90," deg C] # name 2 = c0mS/cm: Conductivity [mS/cm] # name 3 = sbeox0V: Oxygen "Voltage," SBE 43 # name 4 = flECO-AFL: "Fluorescence," Wetlab ECO-AFL/FL [mg/m^3] # name 5 = upoly0: Upoly "0," FLNTU # name 6 = sbeox0ML/L: "Oxygen," SBE 43 "[ml/l]," WS = 1 # name 7 = sbeox0Mg/L: "Oxygen," SBE 43 "[mg/l]," WS = 1 # name 8 = sbeox0PS: "Oxygen," SBE 43 [% "saturation]," WS = 1 # name 9 = nbin: number of scans per bin # name 10 = sal00: Salinity [PSU] # name 11 = potemp090C: Potential Temperature "[ITS-90," deg C] # name 12 = sigma-t00: Density "[sigma-t," Kg/m^3 ] # name 13 = sigma-é00: Density "[sigma-theta," Kg/m^3] # name 14 = depSM: Depth [salt "water," "m]," lat = 47.5 # name 15 = flag: flag # span 0 = "1.000," 10 # span 1 = "9.0940," 10.2977 # span 2 = "29.397097," 31.641217 # span 3 = "2.9524," 3.2714 # span 4 = "1.1907," 6.529 # span 5 = "1.7839778," 2.1325518 # span 6 = "5.92695," 6.63801 # span 7 = "8.47019," 9.48638 # span 8 = "88.58052," 100.13942 # span 9 = "3," 10 # span 10 = "26.0494," 29.2106 # span 11 = "9.0930," 10.2976 # span 12 = "19.9280," 22.5748 # span 13 = "19.9280," 22.575 # span 14 = "0.992," 9.916 # span 15 = "0.0000e+00," 0.00E+00 # interval = decibars: 1 # start_time = May 8 2009 10:34:47 # bad_flag = -9.99E-29 # sensor 0 = Frequency 0 "temperature," "4647," 3-Feb-09 # sensor 1 = Frequency 1 "conductivity," "4647," "03-Feb-09," cpcor = -9.57E-08 # sensor 2 = Pressure Number # sensor 3 = Extrnl Volt 0 WET "Labs," ECO_AFL # sensor 4 = Extrnl Volt 1 userpoly "0," "454," 7/16/08 # sensor 5 = Extrnl Volt 2 "Oxygen," "SBE," "primary," "0718," 31-Jan-09p # datcnv_date = May 29 2009 "22:16:51," 5.30a # datcnv_in = c:\hc09\5893hw.hex c:\hc09\4647.con # datcnv_skipover = 0 # filter_date = May 29 2009 "22:16:52," 5.30a # filter_in = c:\hc09\5893hw.cnv # filter_low_pass_tc_A = 0.5 # filter_low_pass_tc_B = 0 # filter_low_pass_A_vars = c0mS/cm # filter_low_pass_B_vars = # alignctd_date = May 29 2009 "22:16:53," 5.30a # alignctd_in = c:\hc09\5893hw.cnv # alignctd_adv = tv290C "0.500," sbeox0V 5 # loopedit_date = May 29 2009 "22:16:54," 5.30a # loopedit_in = c:\hc09\5893hw.cnv # loopedit_minVelocity = 0.1 # loopedit_excl_bad_scans = yes # Derive_date = May 29 2009 "22:17:24," 5.30a # Derive_in = c:\hc09\5893hw.cnv c:\hc09\4647.con # derive_time_window_docdt = seconds: 1 # binavg_date = May 29 2009 "22:17:25," 5.30a # binavg_in = c:\hc09\5893hw.cnv # binavg_bintype = decibars # binavg_binsize = 1 # binavg_excl_bad_scans = yes # binavg_skipover = 0 # binavg_surface_bin = "no," min = "0.000," max = "0.000," value = 0 # Derive_date = May 29 2009 "22:17:26," 5.30a # Derive_in = c:\hc09\5893hw.cnv c:\hc09\4647.con # file_type = ascii *END* 1 10.2977 29.397097 3.1131 6.529 1.9937028 6.27592 8.96892 94.4882 8 26.0494 10.2976 19.928 19.928 0.992 0.00E+00 2 9.8662 31.142607 3.2598 1.1907 1.9715748 6.60283 9.43611 99.7227 9 28.0941 9.866 21.5865 21.5865 1.983 0.00E+00 3 9.771 31.224445 3.2714 1.5008 2.0352171 6.63801 9.48638 100.13942 9 28.2498 9.7707 21.7225 21.7225 2.975 0.00E+00 4 9.7625 31.261713 3.2477 2.3281 2.1325518 6.58147 9.40557 99.29514 8 28.2933 9.7621 21.7578 21.7578 3.967 0.00E+00 5 9.7448 31.288285 3.1593 2.7627 2.0184835 6.37114 9.10499 96.1083 7 28.3334 9.7443 21.7917 21.7918 4.958 0.00E+00 6 9.634 31.388849 3.0996 3.1507 2.0896517 6.23581 8.9116 93.94634 7 28.5214 9.6334 21.9553 21.9554 5.95 0.00E+00 7 9.3757 31.531551 3.0617 2.9454 1.9931222 6.16478 8.81009 92.54491 10 28.8714 9.375 22.2677 22.2678 6.941 0.00E+00 8 9.3111 31.556815 3.0028 2.8883 1.8252833 6.02888 8.61588 90.41781 9 28.9488 9.3103 22.3378 22.3379 7.933 0.00E+00 9 9.1982 31.611807 2.9764 2.6567 1.7839778 5.97441 8.53803 89.4569 10 29.0959 9.1973 22.4697 22.4698 8.925 0.00E+00 10 9.094 31.641217 2.9524 2.1822 1.8669798 5.92695 8.47019 88.58052 3 29.2106 9.093 22.5748 22.575 9.916 0.00E+00